Search Results for "Camlok"- 46 items found

Camlok "TAG" & "TWG" Wide Jaw Vertical Plate Clamps, Capacity Range from 75kg to 5000kg

Camlok Vertical Plate Lifting Clamp, Jaw Width Options upto 200mm

Camlok "TKA" Tote Pan Grab, Capacity Range from 150kg to 200kg

For lifting and transporting stackable steel tote pans.

Camlok "HGC" Hand Grip Clamp - 250kg

Camlok HGC hand clamp for up to 250kg and 10mm thin plates, weighs only 1.4kg

Camlok Hand Grip Clamp's are suited to the individual transport of light and thin plates. It has a jaw capacity of up to 10mm, and can lift up to 250kg. The Unit itself weighs only 1.4kg.

Camlok "CP" Pile Pitching Clamp - Range from 2000kg to 5000kg

Camlok pile pitching clamps.

The Camlok CP is designed specifically for pitching sheet steel piling, it is NOT designed to extract a driven pile. A rope is fitted for easy release from the ground.

 

Camlok "CG" Girder Lifting Clamp - 2000kg Capacity

Camlok girder section lifting and turning clamps with jaw sizes from 0 - 50mm.

Camlok "PH" Pipe Hooks - Range from 2000kg to 10,000kg

Camlok pipe lifting hooks with shackles. Sold in pairs. Chains not included.

Camlok PH Series Pipe Hooks are used in pairs to handle pipe / tubes etc.  Available with 2 legged chain slings and / or polyurethane coated Type A, 60 to 90 degrees Type B, 90 to 120 degrees. They are manufactured from special high tensile steel

SWL (safe working load) options available: 2 tonnes, 4 tonnes, 6 tonnes, 8 tonnes and 10 tonnes.

Camlok "HG" High Grip Plate Clamp, Capacity 500kg

Camlok High Grip Vertical Plate Lifting Clamp Useful for lifting stainless steel and hardened surface plates.

Camlok "TSH" Swivel Hook Screw Pulling Clamp Range 750kg to 5000kg

With Alloy Safety Shackle Pulling up to 180 degrees

The Camlok series of screwcam clamps can be used on all structural steel plates and sections up to a surface hardness of 300 Brinell. They offer an easy way of attaching pulling equipment to steel structures and can be used for holding and for the correction of alignment problems. This range of clamps is designed for pulling in three planes. The design allows for simultaneous loading in two directions but not for the transportation of plate.

This series of clamps can be used in any combination or number of combinations required they are available in various sizes, lifting capacities and cap sizes.

Camlok "TSZ" Two-Way Pulling Screw Clamp Range 500kg to 7500kg

With two lifting points

The Camlok series of screwcam clamps can be used on all structural steel plates and sections up to a surface hardness of 300 Brinell. They offer an easy way of attaching pulling equipment to steel structures and can be used for holding and for the correction of alignment problems. This range of clamps is designed for pulling in three planes. The design allows for simultaneous loading in two directions but not for the transportation of plate.

This series of clamps can be used in any combination or number of combinations required they are available in various sizes, lifting capacities and cap sizes.

Camlok "RH" Roller Toe Plate Clamp - Range from 1500kg to 5000kg

Camlok Roller Toe Horizontal Plate Lifting Clamps.

This range of horizontal plate clamps has been designed, to be used in pairs, for the horizontal transporting of individual and bundled plate. Whilst the basic design is the same, there are three different versions available.

RH Series - This range is fitted with a steel roller for reduced marking of the plates.
WH Series - The jaw is this range has hardened steel teeth for applications where the marking of plates is not an issue.
WHL Series - With a protective rubber lining on the jaw and the toe plate, this range totally eliminates any risk of marking.

Camlok "DC500" Drum Lifting Clamp - 500kg (Per Clamp)

Camlok Drum Clamp can be used single clamp on sealed or empty drums, 2 clamps and chain sling on open drums.

This range of clamps permit the safe handling of all types of flanged drums with or without lids. This can be used to lift sealed drums on their own, if an open drum is to be lifted without spilling the contents, two clamps can be used with either a two leg chain sling or a small lifting beam and two slings. (Chain sling not included)

Camlok drum clamps are available in the following size - 500kg.

Camlok "TTR" Girder Section Lifting Clamp - Range from 750kg to 3000kg

Camlok Girder Section Lifting Clamp for 5 - 28mm jaw size.

The TTR Series of Clamps have been designed to lift and transport structural steel beams in the horizontal position i.e. with the flanges in the vertical position. The clamp is designed with the hook ring as near as to the centre of gravity of the beam as possible, thus resulting in a near horizontal lift. Long beams should be lifted using 2 clamps attached to opposite beam flanges. The clamp is fitted with a Camlok spring/cam operated safety lock.

Camlok "CX" Heavy Duty Hinged Clamp - Range from 1500kg to 10,000kg

Camlok Heavy Duty Hinged Vertical Plate Lifting Clamp.

The Camlok Series CX range of clamps has been developed especially for the handling of plate at any angle, thus permitting the lifting and handling of awkward shaped plate and fabrications. Single plates can be lifted from the horizontal to the vertical position and vice versa. Vertically racked plates can be turned over due to the in-built lifting eye and link. Standard CX clamps are fitted with a cam operated closing mechanism that can, if preferred, be replaced with a chain pull open /close mechanism. Clamps are fitted with hardened serrated teeth, jaws and pads that are suitable for gripping steel plate up to a hardness of 300 Brinell.

Camlok "PP" Pile Pulling Clamp - Range from 3000kg to 8000kg

Camlok Pile Pulling Clamp.

Camlok "THK" Thin Sheet Horizontal Plate Clamps, Range 750kg to 9000kg

Camlok Horizontal Plate Lifting Clamps, Sold in Pairs, Designed for Lifting Single Thin Sheet / Plate.

The Camlok THK Clamp has a jaw that pivots in the reverse direction to our normal horizontal clamps and is designed to lift and handle thin sheet plate that tend to sag when lifted. The reverse jaw feature ensures that the clamp grip increases the more the plate deflects under its own self weight. Clamps are used in pairs with a 2 legged chain sling (maximum included angle not to exceed 60º). Two pairs of clamps supported from a lifting beam must be used when handling long plates. Single plates only can be lifted.

Camlok "TSB" Gentle Grip Non-Marking Plate Clamps, Range from 40kg to 1250kg

Camlok Non-Marking Plate Clamps for 0 - 65mm Plate

The TSB gentle grip clamp is designed to lift and handle various types of material such as steel, timber, plastics, laminates etc. without causing damage to the surface finish. The fixed pad and horizontally moving jaw are lined with hard wearing rubber. The lateral gripping load is transmitted to the moving jaw via a short length of chain routed between two chain pulleys. The clamp can be used to lift plates from the horizontal to vertical position and vice versa.

Options on Camlok grip non marking plate clamp - 350kg/plate diameter 0 - 65mm, 750kg/plate diameter 0 - 65mm, 1250kg/jaw opening 0 - 65mm.

Camlok "TTT" Girder Section Clamp - Range from 500kg to 3000kg

Camlok Vertical Girder Section Clamp.

The TTT Series Clamp is a variant of the TTG clamp but this clamp is designed to be used in pairs supported from a 2 legged chain sling. The bottom toe plate is split thus enabling the clamp to be attached to the end of the structural steel beam. The clamp is fitted with a spring operated safety lock. Particularly used for erecting structural beams on construction sites.

The Camlok series of TTT clamps can be used on girders up to a surface hardness of 300 Brinell. Girders can be lifted vertically from their ends so that steel beams can be transported with the flanges in a horizontal position.

Camlok "TTG" Girder Clamp, Range from 500kg to 7500kg

Camlok Horizontal Flange Girder Section Lifting and Stacking Clamp.

The TTG Girder Clamp is designed to lift and transport structural steel beams in the vertical position i.e with the flanges in the horizontal position. The clamp is fitted with a Camlok spring operated safety lock and is operated by pulling the locking handle upwards. Long beams should be lifted with two clamps attached on opposite beam flanges, the clamps supported from a lifting beam.

The TTG is ideal for lifting and transporting structural steel beams and girders. Long beams can be lifted using 2 clamps attached to opposite beam flanges. The clamp is fitted with a Camlok spring / cam operated safety lock.

 

Camlok "TCS" Coil Turning Hooks - Range from 500kg to 3000kg

Coil Turning Hooks, Camlok TCS.

Camlok BTG Concrete Pipe Clamps, Capacity Range 1500kg or 3000kg

Camlok Concrete Pipe Section Lifting Clamps.

The Camlok BTG clamp is designed to vertically lift and position concrete manhole pipes. The clamps can be adjusted to different wall thicknesses using the adjusting pin and the holes inside the clamping arms. The BTG concrete pipe clamp is designed to vertically lift and position concrete manhole pipes. The clamps can be adjusted to different wall thicknesses using the adjusting pin and the holes inside the clamping arm. The clamps can be used in pairs with 2 leg chain slings or with 3 clamps and a 3 leg chain sling for larger diameters, providing they are attached in a way that the load is evenly distributed. Use of the BTG clamp enables the manhole trench size to be minimized and facilitates accurate pipe positioning.